platform_hardware_interfaces/power/stats/1.0/IPowerStats.hal

/*
 * Copyright (C) 2018 The Android Open Source Project
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */
package android.hardware.power.stats@1.0;

interface IPowerStats {

    /**
     * Rail information:
     * Reports information related to the rails being monitored.
     *
     * @return rails Information about monitored rails.
     * @return status SUCCESS on success or NOT_SUPPORTED if
     *     feature is not enabled or FILESYSTEM_ERROR on filesystem nodes
     *     access error.
     */
    getRailInfo()
        generates(vec<RailInfo> rails, Status status);

    /**
     * Rail level energy measurements for low frequency clients:
     * Reports accumulated energy since boot on each rail.
     *
     * @param railIndices Indices of rails for which data is required.
     *     To get data for all rails pass an empty vector. Rail name to
     *     index mapping can be queried from getRailInfo() API.
     * @return data Energy values since boot for all requested rails.
     * @return status SUCCESS on success or NOT_SUPPORTED if
     *     feature is not enabled or FILESYSTEM_ERROR on filesystem nodes
     *     access error.
     */
    getEnergyData(vec<uint32_t> railIndices)
        generates(vec<EnergyData> data, Status status);

    /**
     * Stream rail level power measurements for high frequency clients:
     * Streams accumulated energy since boot on each rail. This API is
     * asynchronous.
     *
     * @param timeMs Time(in ms) for which energyData should be streamed
     * @param samplingRate Frequency(in Hz) at which samples should be
     *     captured. If the requested sampling rate is not supported then
     *     SUCCESS is returned and numSamples are reported back according
     *     to the supported sampling rate.
     * @return mqDesc Blocking Synchronous Fast Message Queue descriptor - One
     *     writer(power.stats HAL) and one reader are supported. Data is
     *     present in the following format in the queue:
     *     +-----------------------+       <--
     *     | EnergyData for rail 1 |         |
     *     +-----------------------+         |
     *     | EnergyData for rail 2 |         |
     *     +-----------------------+         |
     *     |          .            |         |-- 1st Sample
     *     |          .            |         |
     *     |          .            |         |
     *     +-----------------------+         |
     *     | EnergyData for rail n |         |
     *     +-----------------------+       <--
     *     |          .            |
     *     |          .            |
     *     |          .            |
     *     +-----------------------+       <--
     *     | EnergyData for rail 1 |         |
     *     +-----------------------+         |
     *     | EnergyData for rail 2 |         |
     *     +-----------------------+         |
     *     |          .            |         |-- kth Sample
     *     |          .            |         |
     *     |          .            |         |
     *     +-----------------------+         |
     *     | EnergyData for rail n |         |
     *     +-----------------------+       <--
     *
     *     where,
     *     n = railsPerSample
     *     k = numSamples
     *
     * @return numSamples Number of samples which will be generated in timeMs.
     * @return railsPerSample Number of rails measured per sample.
     * @return status SUCCESS on success or FILESYSTEM_ERROR on filesystem
     *     nodes access or NOT_SUPPORTED if feature is not enabled or
     *     INSUFFICIENT_RESOURCES if there are not enough resources.
     */
    streamEnergyData(uint32_t timeMs, uint32_t samplingRate)
        generates(fmq_sync<EnergyData> mqDesc, uint32_t numSamples,
                uint32_t railsPerSample, Status status);

    /**
     * PowerEntity information:
     * Reports information related to all supported PowerEntity(s) for which
     * data is available. A PowerEntity is defined as a platform subsystem,
     * peripheral, or power domain that impacts the total device power
     * consumption.
     *
     * @return powerEntityInfos List of information on each PowerEntity
     * @return status SUCCESS on success, NOT_SUPPORTED if feature is not
     *     enabled, FILESYSTEM_ERROR if there was an error accessing the
     *     filesystem.
     */
    getPowerEntityInfo()
        generates(vec<PowerEntityInfo> powerEntityInfos, Status status);

    /**
     * PowerEntity state information:
     * Reports the set of power states for which the specified
     * PowerEntity(s) provide residency data.
     *
     * @param powerEntityIds collection of IDs of PowerEntity(s) for which
     *     state information is requested. PowerEntity name to ID mapping may
     *     be queried from getPowerEntityInfo(). To get state space
     *     information for all PowerEntity(s) pass an empty vector.
     *
     * @return powerEntityStateSpaces PowerEntity state space information for
     *     each specified PowerEntity that provides state space information.
     * @return status SUCCESS on success, NOT_SUPPORTED if feature is not
     *     enabled, FILESYSTEM_ERROR if there was an error accessing the
     *     filesystem, INVALID_INPUT if any requested PowerEntity(s) do not
     *     provide state space information and there was not a filesystem error.
     */
    getPowerEntityStateInfo(vec<uint32_t> powerEntityIds)
        generates(vec<PowerEntityStateSpace> powerEntityStateSpaces,
                  Status status);

    /**
     * PowerEntity residencies for low frequency clients:
     * Reports accumulated residency data for each specified PowerEntity.
     * Each PowerEntity may reside in one of multiple states. It may also
     * transition to another state. Residency data is an accumulation of time
     * that a specified PowerEntity resided in each of its possible states,
     * the number of times that each state was entered, and a timestamp
     * corresponding to the last time that state was entered. Data is
     * accumulated starting from the last time the PowerEntity was reset.
     *
     * @param powerEntityId collection of IDs of PowerEntity(s) for which
     *     residency data is requested. PowerEntity name to ID mapping may
     *     be queried from getPowerEntityInfo(). To get state residency
     *     data for all PowerEntity(s) pass an empty vector.
     * @return stateResidencyResults state residency data for each specified
     *     PowerEntity that provides state residency data.
     * @return status SUCCESS on success, NOT_SUPPORTED if feature is not
     *     enabled, FILESYSTEM_ERROR if there was an error accessing the
     *     filesystem, INVALID_INPUT if any requested PowerEntity(s) do not
     *     provide state residency data and there was not a filesystem error.
     */
    getPowerEntityStateResidencyData(vec<uint32_t> powerEntityIds)
        generates(vec<PowerEntityStateResidencyResult> stateResidencyResults,
                  Status status);
};