platform_hardware_interfaces/tv/tuner/1.0/ILnb.hal
Henry Fang 865220991a Add Filter linkage and seperate interface
Test: Manual
bug: 135708935
Change-Id: I5782a183936ffca4f345d14c353ad34210f12df7
(cherry picked from commit e5125a89ab)
Merged-In: I5782a183936ffca4f345d14c353ad34210f12df7
2019-10-26 00:29:01 +00:00

106 lines
3.9 KiB
Text

/*
* Copyright (C) 2019 The Android Open Source Project
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
package android.hardware.tv.tuner@1.0;
import ILnbCallback;
/**
* A Tuner LNB (low-noise block downconverter) is used by satellite frontend
* to receive the microwave signal from the satellite, amplify it, and
* downconvert the frequency to a lower frequency.
*/
interface ILnb {
/**
* Set the lnb callback.
*
* ILnbCallback is used by the client to receive events from the Lnb.
* Only one callback per ILnb instance is supported. The callback
* will be replaced if it's set again.
*
* @param callback Callback object to pass Lnb events to the system.
* The previously registered callback must be replaced with this one.
* It can be null.
* @return result Result status of the operation.
* SUCCESS if successful,
* INVALID_STATE if callback can't be set at current stage,
* UNKNOWN_ERROR if callback setting failed for other reasons.
*/
setCallback(ILnbCallback callback) generates (Result result);
/**
* Set the lnb's power voltage.
*
* @param voltage the power's voltage the Lnb to use.
* @return result Result status of the operation.
* SUCCESS if successful,
* INVALID_ARGUMENT if the selected voltage isn't allowed,
* UNKNOWN_ERROR if failed for other reasons.
*/
setVoltage(LnbVoltage voltage) generates (Result result);
/**
* Set the lnb's tone mode.
*
* @param tone the tone mode the Lnb to use.
* @return result Result status of the operation.
* SUCCESS if successful,
* INVALID_ARGUMENT if the selected tone mode isn't allowed,
* UNKNOWN_ERROR if failed for other reasons.
*/
setTone(LnbTone tone) generates (Result result);
/**
* Select the lnb's position.
*
* @param position the position the Lnb to use.
* @return result Result status of the operation.
* SUCCESS if successful,
* INVALID_ARGUMENT if the selected position isn't allowed,
* UNKNOWN_ERROR if failed for other reasons.
*/
setSatellitePosition(LnbPosition position) generates (Result result);
/**
* Sends DiSEqC (Digital Satellite Equipment Control) message.
*
* Client sends DiSeqc message to DiSEqc to LNB. The response message from
* the device comes back to the client through frontend's callback
* onDiseqcMessage.
*
* @param diseqcMessage a byte array of data for DiSEqC message which is
* specified by EUTELSAT Bus Functional Specification Version 4.2.
*
* @return result Result status of the operation.
* SUCCESS if successful,
* INVALID_STATE if the frontend can't send DiSEqc Message, such as
* cable frontend.
* UNKNOWN_ERROR if failed for other reasons.
*/
sendDiseqcMessage(vec<uint8_t> diseqcMessage) generates (Result result);
/**
* Releases the LNB instance
*
* Associated resources are released. close may be called more than once.
* Calls to any other method after this will return an error
*
* @return result Result status of the operation.
* SUCCESS if successful,
* UNKNOWN_ERROR if failed for other reasons.
*/
close() generates (Result result);
};