238 lines
12 KiB
C
238 lines
12 KiB
C
|
||
#include "wifi_hal.h"
|
||
#include "gscan.h"
|
||
|
||
#ifndef __WIFI_HAL_RTT_H__
|
||
#define __WIFI_HAL_RTT_H__
|
||
|
||
/* Ranging status */
|
||
typedef enum {
|
||
RTT_STATUS_SUCCESS = 0,
|
||
RTT_STATUS_FAILURE = 1, // general failure status
|
||
RTT_STATUS_FAIL_NO_RSP = 2, // target STA does not respond to request
|
||
RTT_STATUS_FAIL_REJECTED = 3, // request rejected. Applies to 2-sided RTT only
|
||
RTT_STATUS_FAIL_NOT_SCHEDULED_YET = 4,
|
||
RTT_STATUS_FAIL_TM_TIMEOUT = 5, // timing measurement times out
|
||
RTT_STATUS_FAIL_AP_ON_DIFF_CHANNEL = 6, // Target on different channel, cannot range
|
||
RTT_STATUS_FAIL_NO_CAPABILITY = 7, // ranging not supported
|
||
RTT_STATUS_ABORTED = 8, // request aborted for unknown reason
|
||
RTT_STATUS_FAIL_INVALID_TS = 9, // Invalid T1-T4 timestamp
|
||
RTT_STATUS_FAIL_PROTOCOL = 10, // 11mc protocol failed
|
||
RTT_STATUS_FAIL_SCHEDULE = 11, // request could not be scheduled
|
||
RTT_STATUS_FAIL_BUSY_TRY_LATER = 12, // responder cannot collaborate at time of request
|
||
RTT_STATUS_INVALID_REQ = 13, // bad request args
|
||
RTT_STATUS_NO_WIFI = 14, // WiFi not enabled
|
||
RTT_STATUS_FAIL_FTM_PARAM_OVERRIDE = 15 // Responder overrides param info, cannot range with new params
|
||
} wifi_rtt_status;
|
||
|
||
/* RTT peer type */
|
||
typedef enum {
|
||
RTT_PEER_AP = 0x1,
|
||
RTT_PEER_STA = 0x2,
|
||
RTT_PEER_P2P_GO = 0x3,
|
||
RTT_PEER_P2P_CLIENT = 0x4,
|
||
RTT_PEER_NAN = 0x5
|
||
} rtt_peer_type;
|
||
|
||
/* RTT Measurement Bandwidth */
|
||
typedef enum {
|
||
WIFI_RTT_BW_5 = 0x01,
|
||
WIFI_RTT_BW_10 = 0x02,
|
||
WIFI_RTT_BW_20 = 0x04,
|
||
WIFI_RTT_BW_40 = 0x08,
|
||
WIFI_RTT_BW_80 = 0x10,
|
||
WIFI_RTT_BW_160 = 0x20
|
||
} wifi_rtt_bw;
|
||
|
||
/* RTT Measurement Preamble */
|
||
typedef enum {
|
||
WIFI_RTT_PREAMBLE_LEGACY = 0x1,
|
||
WIFI_RTT_PREAMBLE_HT = 0x2,
|
||
WIFI_RTT_PREAMBLE_VHT = 0x4
|
||
} wifi_rtt_preamble;
|
||
|
||
/* RTT Type */
|
||
typedef enum {
|
||
RTT_TYPE_1_SIDED = 0x1,
|
||
RTT_TYPE_2_SIDED = 0x2,
|
||
} wifi_rtt_type;
|
||
|
||
/* RTT configuration */
|
||
typedef struct {
|
||
mac_addr addr; // peer device mac address
|
||
wifi_rtt_type type; // 1-sided or 2-sided RTT
|
||
rtt_peer_type peer; // optional - peer device hint (STA, P2P, AP)
|
||
wifi_channel_info channel; // Required for STA-AP mode, optional for P2P, NBD etc.
|
||
unsigned burst_period; // Time interval between bursts (units: 100 ms).
|
||
// Applies to 1-sided and 2-sided RTT multi-burst requests.
|
||
// Range: 0-31, 0: no preference by initiator (2-sided RTT)
|
||
unsigned num_burst; // Total number of RTT bursts to be executed. It will be
|
||
// specified in the same way as the parameter "Number of
|
||
// Burst Exponent" found in the FTM frame format. It
|
||
// applies to both: 1-sided RTT and 2-sided RTT. Valid
|
||
// values are 0 to 15 as defined in 802.11mc std.
|
||
// 0 means single shot
|
||
// The implication of this parameter on the maximum
|
||
// number of RTT results is the following:
|
||
// for 1-sided RTT: max num of RTT results = (2^num_burst)*(num_frames_per_burst)
|
||
// for 2-sided RTT: max num of RTT results = (2^num_burst)*(num_frames_per_burst - 1)
|
||
unsigned num_frames_per_burst; // num of frames per burst.
|
||
// Minimum value = 1, Maximum value = 31
|
||
// For 2-sided this equals the number of FTM frames
|
||
// to be attempted in a single burst. This also
|
||
// equals the number of FTM frames that the
|
||
// initiator will request that the responder send
|
||
// in a single frame.
|
||
unsigned num_retries_per_rtt_frame; // number of retries for a failed RTT frame. Applies
|
||
// to 1-sided RTT only. Minimum value = 0, Maximum value = 3
|
||
|
||
//following fields are only valid for 2-side RTT
|
||
unsigned num_retries_per_ftmr; // Maximum number of retries that the initiator can
|
||
// retry an FTMR frame.
|
||
// Minimum value = 0, Maximum value = 3
|
||
byte LCI_request; // 1: request LCI, 0: do not request LCI
|
||
byte LCR_request; // 1: request LCR, 0: do not request LCR
|
||
unsigned burst_duration; // Applies to 1-sided and 2-sided RTT. Valid values will
|
||
// be 2-11 and 15 as specified by the 802.11mc std for
|
||
// the FTM parameter burst duration. In a multi-burst
|
||
// request, if responder overrides with larger value,
|
||
// the initiator will return failure. In a single-burst
|
||
// request if responder overrides with larger value,
|
||
// the initiator will sent TMR_STOP to terminate RTT
|
||
// at the end of the burst_duration it requested.
|
||
wifi_rtt_preamble preamble; // RTT preamble to be used in the RTT frames
|
||
wifi_rtt_bw bw; // RTT BW to be used in the RTT frames
|
||
} wifi_rtt_config;
|
||
|
||
/* RTT results */
|
||
typedef struct {
|
||
mac_addr addr; // device mac address
|
||
unsigned burst_num; // burst number in a multi-burst request
|
||
unsigned measurement_number; // Total RTT measurement frames attempted
|
||
unsigned success_number; // Total successful RTT measurement frames
|
||
byte number_per_burst_peer; // Maximum number of "FTM frames per burst" supported by
|
||
// the responder STA. Applies to 2-sided RTT only.
|
||
// If reponder overrides with larger value:
|
||
// - for single-burst request initiator will truncate the
|
||
// larger value and send a TMR_STOP after receiving as
|
||
// many frames as originally requested.
|
||
// - for multi-burst request, initiator will return
|
||
// failure right away.
|
||
wifi_rtt_status status; // ranging status
|
||
byte retry_after_duration; // When status == RTT_STATUS_FAIL_BUSY_TRY_LATER,
|
||
// this will be the time provided by the responder as to
|
||
// when the request can be tried again. Applies to 2-sided
|
||
// RTT only. In sec, 1-31sec.
|
||
wifi_rtt_type type; // RTT type
|
||
wifi_rssi rssi; // average rssi in 0.5 dB steps e.g. 143 implies -71.5 dB
|
||
wifi_rssi rssi_spread; // rssi spread in 0.5 dB steps e.g. 5 implies 2.5 dB spread (optional)
|
||
wifi_rate tx_rate; // 1-sided RTT: TX rate of RTT frame.
|
||
// 2-sided RTT: TX rate of initiator's Ack in response to FTM frame.
|
||
wifi_rate rx_rate; // 1-sided RTT: TX rate of Ack from other side.
|
||
// 2-sided RTT: TX rate of FTM frame coming from responder.
|
||
wifi_timespan rtt; // round trip time in 0.1 nanoseconds
|
||
wifi_timespan rtt_sd; // rtt standard deviation in 0.1 nanoseconds
|
||
wifi_timespan rtt_spread; // difference between max and min rtt times recorded
|
||
int distance; // distance in cm (optional)
|
||
int distance_sd; // standard deviation in cm (optional)
|
||
int distance_spread; // difference between max and min distance recorded (optional)
|
||
wifi_timestamp ts; // time of the measurement (in microseconds since boot)
|
||
int burst_duration; // in ms, actual time taken by the FW to finish one burst
|
||
// measurement. Applies to 1-sided and 2-sided RTT.
|
||
int negotiated_burst_num; // Number of bursts allowed by the responder. Applies
|
||
// to 2-sided RTT only.
|
||
wifi_information_element *LCI; // for 11mc only
|
||
wifi_information_element *LCR; // for 11mc only
|
||
} wifi_rtt_result;
|
||
|
||
/* RTT result callback */
|
||
typedef struct {
|
||
void (*on_rtt_results) (wifi_request_id id, unsigned num_results, wifi_rtt_result *rtt_result[]);
|
||
} wifi_rtt_event_handler;
|
||
|
||
/* API to request RTT measurement */
|
||
wifi_error wifi_rtt_range_request(wifi_request_id id, wifi_interface_handle iface,
|
||
unsigned num_rtt_config, wifi_rtt_config rtt_config[], wifi_rtt_event_handler handler);
|
||
|
||
/* API to cancel RTT measurements */
|
||
wifi_error wifi_rtt_range_cancel(wifi_request_id id, wifi_interface_handle iface,
|
||
unsigned num_devices, mac_addr addr[]);
|
||
|
||
/* NBD ranging channel map */
|
||
typedef struct {
|
||
wifi_channel availablity[32]; // specifies the channel map for each of the 16 TU windows
|
||
// frequency of 0 => unspecified; which means firmware is
|
||
// free to do whatever it wants in this window.
|
||
} wifi_channel_map;
|
||
|
||
/* API to start publishing the channel map on responder device in a NBD cluster.
|
||
Responder device will take this request and schedule broadcasting the channel map
|
||
in a NBD ranging attribute in a SDF. DE will automatically remove the ranging
|
||
attribute from the OTA queue after number of DW specified by num_dw
|
||
where Each DW is 512 TUs apart */
|
||
wifi_error wifi_rtt_channel_map_set(wifi_request_id id,
|
||
wifi_interface_handle iface, wifi_channel_map *params, unsigned num_dw);
|
||
|
||
/* API to clear the channel map on the responder device in a NBD cluster.
|
||
Responder device will cancel future ranging channel request, starting from next
|
||
DW interval and will also stop broadcasting NBD ranging attribute in SDF */
|
||
wifi_error wifi_rtt_channel_map_clear(wifi_request_id id, wifi_interface_handle iface);
|
||
|
||
// Preamble definition for bit mask used in wifi_rtt_capabilities
|
||
#define PREAMBLE_LEGACY 0x1
|
||
#define PREAMBLE_HT 0x2
|
||
#define PREAMBLE_VHT 0x4
|
||
|
||
// BW definition for bit mask used in wifi_rtt_capabilities
|
||
#define BW_5_SUPPORT 0x1
|
||
#define BW_10_SUPPORT 0x2
|
||
#define BW_20_SUPPORT 0x4
|
||
#define BW_40_SUPPORT 0x8
|
||
#define BW_80_SUPPORT 0x10
|
||
#define BW_160_SUPPORT 0x20
|
||
|
||
/* RTT Capabilities */
|
||
typedef struct {
|
||
byte rtt_one_sided_supported; // if 1-sided rtt data collection is supported
|
||
byte rtt_ftm_supported; // if ftm rtt data collection is supported
|
||
byte lci_support; // if initiator supports LCI request. Applies to 2-sided RTT
|
||
byte lcr_support; // if initiator supports LCR request. Applies to 2-sided RTT
|
||
byte preamble_support; // bit mask indicates what preamble is supported by initiator
|
||
byte bw_support; // bit mask indicates what BW is supported by initiator
|
||
} wifi_rtt_capabilities;
|
||
|
||
/* RTT capabilities of the device */
|
||
wifi_error wifi_get_rtt_capabilities(wifi_interface_handle iface, wifi_rtt_capabilities *capabilities);
|
||
|
||
/* debugging definitions */
|
||
enum {
|
||
RTT_DEBUG_DISABLE,
|
||
RTT_DEBUG_LOG,
|
||
RTT_DEBUG_PROTO,
|
||
RTT_DEBUG_BURST,
|
||
RTT_DEBUG_ACCURACY,
|
||
RTT_DEBUG_LOGDETAIL
|
||
}; //rtt debug type
|
||
|
||
enum {
|
||
RTT_DEBUG_FORMAT_TXT,
|
||
RTT_DEBUG_FORMAT_BINARY
|
||
}; //rtt debug format
|
||
|
||
typedef struct rtt_debug {
|
||
unsigned version;
|
||
unsigned len; // total length of after len field
|
||
unsigned type; // rtt debug type
|
||
unsigned format; //rtt debug format
|
||
char dbuf[0]; // debug content
|
||
} rtt_debug_t;
|
||
|
||
/* set configuration for debug */
|
||
wifi_error wifi_rtt_debug_cfg(wifi_interface_handle h, unsigned rtt_dbg_type, char *cfgbuf, unsigned cfg_buf_size);
|
||
/* get the debug information */
|
||
wifi_error wifi_rtt_debug_get(wifi_interface_handle h, rtt_debug_t **debugbuf);
|
||
/* free the debug buffer */
|
||
wifi_error wifi_rtt_debug_free(wifi_interface_handle h, rtt_debug_t *debugbuf);
|
||
|
||
#endif
|
||
|