platform_system_core/fs_mgr/README.overlayfs.md

115 lines
4 KiB
Markdown
Raw Normal View History

Android Overlayfs integration with adb remount
==============================================
Introduction
------------
Users working with userdebug or eng builds expect to be able to
remount the system partition as read-write and then add or modify
any number of files without reflashing the system image, which is
understandably efficient for a development cycle.
Limited memory systems that chose to use readonly filesystems like
*squashfs*, or *Logical Resizable Android Partitions* which land
system partition images right-sized, and with filesystem that have
been deduped on the block level to compress the content; means that
either a remount is not possible directly, or when done offers
little or no utility because of remaining space limitations or
support logistics.
*Overlayfs* comes to the rescue for these debug scenarios, and logic
will _automatically_ setup backing storage for a writable filesystem
as an upper reference, and mount overtop the lower. These actions
will be performed in the **adb disable-verity** and **adb remount**
requests.
Operations
----------
### Cookbook
The typical action to utilize the remount facility is:
$ adb root
$ adb disable-verity
$ adb reboot
$ adb wait-for-device
$ adb root
$ adb remount
Followed by one of the following:
$ adb stop
$ adb sync
$ adb start
$ adb reboot
*or*
$ adb push <source> <destination>
$ adb reboot
Note that the sequence above:
$ adb disable-verity
$ adb reboot
*or*
$ adb remount
can be replaced in both places with:
$ adb remount -R
which will not reboot if everything is already prepared and ready
to go.
None of this changes if *overlayfs* needs to be engaged.
The decisions whether to use traditional direct filesystem remount,
or one wrapped by *overlayfs* is automatically determined based on
a probe of the filesystem types and space remaining.
### Backing Storage
When *overlayfs* logic is feasible, it will use either the
**/cache/overlay/** directory for non-A/B devices, or the
**/mnt/scratch/overlay** directory for A/B devices that have
access to *Logical Resizeable Android Partitions*.
The backing store is used as soon as possible in the boot
process and can occur at first stage init, or at the
mount_all init rc commands.
This early as possible attachment of *overlayfs* means that
*sepolicy* or *init* itself can also be pushed and used after
the exec phases that accompany each stage.
Caveats
-------
- Space used in the backing storage is on a file by file basis
and will require more space than if updated in place. As such
it is important to be mindful of any wasted space, for instance
**BOARD_<partition>IMAGE_PARTITION_RESERVED_SIZE** being defined
will have a negative impact on the overall right-sizing of images
and thus free dynamic partition space.
- Kernel must have CONFIG_OVERLAY_FS=y and will need to be patched
with "*overlayfs: override_creds=off option bypass creator_cred*"
if higher than 4.6.
- *adb enable-verity* will free up overlayfs and as a bonus the
device will be reverted pristine to before any content was updated.
Update engine does not take advantage of this, will perform a full OTA.
- Update engine may not run if *fs_mgr_overlayfs_is_setup*() reports
true as adb remount overrides are incompatable with an OTA resources.
- For implementation simplicity on retrofit dynamic partition devices,
take the whole alternate super (eg: if "*a*" slot, then the whole of
"*system_b*").
Since landing a filesystem on the alternate super physical device
without differentiating if it is setup to support logical or physical,
the alternate slot metadata and previous content will be lost.
- If dynamic partitions runs out of space, resizing a logical
partition larger may fail because of the scratch partition.
If this happens, either fastboot flashall or adb enable-verity can
be used to clear scratch storage to permit the flash.
Then reinstate the overrides and continue.
- File bugs or submit fixes for review.